Aim-TTi LDH400P DC 400W, 500V, 16A Electronic Load
Använd vår chatt för personlig support. Eller kontakta oss via +45 31 33 18 19 eller salg@GOmeasure.dk
- Allsidig lösning för direkt testning av likströmskällor och PFC:er
- Konstant ström, resistans, ledningsförmåga och effektlägen
- Bred spännings- och strömområde, 10 till 500V och 0 till 16A
- 400 watt kontinuerlig avledning vid 28°C (360W vid 40°C)
- Hög upplösning och noggrannhet för nivåinställning
- Inbyggd transiente generator med variabel stigning
- Strömövervakningsutgång för vågformsvisning
- Variabel frånkopplingsspänning för batteritestning
- Högupplöst bakgrundsbelyst grafisk LCD med mjukknappskontroll
- Analog fjärrkontroll av nivåer och TTL-kontroll av på/av och transientväxling
- Fram- och bakre ingångsterminaler
- Lastingångar klassade till CAT II (300V)
- Full busskontroll via USB, RS232 och LXI-kompatibla LAN-gränssnitt
- GPIB-alternativ
Upptäck möjligheterna
Mer information
Beskrivning
Aim-TTi LDH400P DC 400W, 500V, 16A Electronic Load
CAT II (300V) RATING
The Aim-TTi LDH400P load inputs are rated to CAT II (300V), this allows the direct testing of PFCs and mains connected power supplies to be simplified using the LDH400P by eliminating the need for an isolation transformer, saving bench space and cost.CURRENT WAVEFORM MONITOR
It is often important to be able to observe the load current waveform on an oscilloscope. The LD series provides a calibrated monitor output for this purpose as well as a sync output from the transient generator. The LDH400P monitor output is ground (chassis) referenced and isolated from the load input, thus allowing it to be connected to a ground oscilloscope.TRANSIENT GENERATOR AND VARIABLE SLEW
The LD series incorporates a full variable frequency, variable duty cycle transient generator. Switching between the two preset levels can be done at any frequency between 0.01Hz and 10kHz. The transient generator can be used in all operating modes. The rate of change between levels (slew rate) is controllable over a wide range. Slew rate control applies to all changes of level including remote control and manual changes between level A and level B. A slow-start function can be selected for situations where latching would otherwise occur at switch-on.HIGH RESOLUTION SETTING/MEASUREMENT
The two operating levels for each operating mode are settable to high precision. Levels are displayed using four digit meters which provide resolution down to 1mA, 1mV and 1mW. The meters have an accuracy of 0.1% for voltage and 0.2% for current.For more information: Aim-TTi LDH400P Series
Dokument
Aim-TTi LDH400P DC 400W, 500V, 16A Electronic Load
Aim-TTi LD400 Series DatasheetAlternativ
Video
Aim-TTi LDH400P DC 400W, 500V, 16A Electronic Load
CAT II (300V) RATING
The Aim-TTi LDH400P load inputs are rated to CAT II (300V), this allows the direct testing of PFCs and mains connected power supplies to be simplified using the LDH400P by eliminating the need for an isolation transformer, saving bench space and cost.CURRENT WAVEFORM MONITOR
It is often important to be able to observe the load current waveform on an oscilloscope. The LD series provides a calibrated monitor output for this purpose as well as a sync output from the transient generator. The LDH400P monitor output is ground (chassis) referenced and isolated from the load input, thus allowing it to be connected to a ground oscilloscope.TRANSIENT GENERATOR AND VARIABLE SLEW
The LD series incorporates a full variable frequency, variable duty cycle transient generator. Switching between the two preset levels can be done at any frequency between 0.01Hz and 10kHz. The transient generator can be used in all operating modes. The rate of change between levels (slew rate) is controllable over a wide range. Slew rate control applies to all changes of level including remote control and manual changes between level A and level B. A slow-start function can be selected for situations where latching would otherwise occur at switch-on.HIGH RESOLUTION SETTING/MEASUREMENT
The two operating levels for each operating mode are settable to high precision. Levels are displayed using four digit meters which provide resolution down to 1mA, 1mV and 1mW. The meters have an accuracy of 0.1% for voltage and 0.2% for current.For more information: Aim-TTi LDH400P Series