Tekbox TBLLA-2M Large Loop Antenna
Använd vår chatt för personlig support. Eller kontakta oss via +45 31 33 18 19 eller salg@GOmeasure.dk
- Typ: Stor loopantenn (trippel loop)
- Frekvensområde: 9 kHz– 30 MHz
- Standarder: CISPR 16-1-4, CISPR 15
- Loopar: 3 vinkelräta loopar med 2m diameter
- Loopkonstruktion: RG223U-sektioner med överformade slitsar inuti PEX-rör
- RF-transduktors överföringsimpedans: typisk 0 dBΩ; 1V/A @ 9kHz till 30 MHz
- RF-transduktors utgångskontakt: N-hona, 50 Ω
- Antennavalideringsfaktor: inom ±2 dB jämfört med den teoretiska valideringsfaktorn för 2m diameter LLA som anges i CISPR 16-1-4
- Effektiv antennkorrektionsfaktor: 0 dB
- CM-motståndet hos ferritabsorberarna: > 200 Ω @ 10 MHz
- Mechaniska dimensioner: L x B x H: 2062 mm x 2062 mm x 2547 mm (81.2” x 81.2” x
- 100”)
- Vikt: 25 kg (55.12 lbs)
%0AFrekvensomr%C3%A5de:%209%20kHz%E2%80%93%2030%20MHz%0AStandarder:%20CISPR%2016-1-4,%20CISPR%2015%0ALoopar:%203%20vinkelr%C3%A4ta%20loopar%20med%202m%20diameter%0ALoopkonstruktion:%20RG223U-sektioner%20med%20%C3%B6verformade%20...
){kind=link}
Upptäck möjligheterna
Mer information
Beskrivning
The TBLLA-2M is a large loop antenna (LLA) with three orthogonal loops, as required by CISPR 16 -1-4 and CISPR 15 / EN 55015.
The LLA is used to measure the current induced by the magnetic field emitted by luminaries. Section 4.4 of EN 55015 specifies the test setup and measuring procedures.
The TBLLA-2M consists of three perpendicular 2-meter diameter loop antennas on three orthogonal planes (X/Y/Z), set on lightweight hollow WPC frames with a total height of 2.5m. The loops lowest point is 0.5m above ground. Each loop element receives magnetic field radiation normal to the containing plane and generates a voltage signal proportionate to the strength of the H -field radiation at the output port of the RF transducer connected to the loop.
The TBLLA-2M is equipped with three TekBox TBCCP1-2K70 coaxial RF current monitoring probes (transducers), with a flat transfer impedance of 0 dBΩ (1V/A) from 9 kHz to 30 MHz when loaded with 50Ω. The kit comprises all required coaxial cables, ferrite clamps, a manual RF coaxial switch to select loops, and a TBTP3 tripod with a plastic DUT support plate.
A calibration dipole with support structure is available as optional accessory.
SPECIFICATIONS
- Type: Large Loop Antenna (triple loop)
- Frequency range: 9 kHz– 30 MHz
- Standards: CISPR 16-1-4, CISPR 15
- Loops: 3 perpendicular loops with 2m diameter
- Loop construction: RG223U sections with over-molded slits inside PEX tube
- RF transducer transfer impedance: typical 0 dBΩ ; 1V/A @ 9kHz to 30 MHz
- RF transducer output connector: N-female, 50 Ω
- Antenna validation factor: within ±2 dB compared to the theoretical validation factor for 2m diameter LLA given in CISPR 16-1-4
- Effective antenna correction factor: 0 dB
- CM resistance of the ferrite absorbers: > 200 Ω @ 10 MHz
- Mechanical Dimensions: L x W x H: 2062 mm x 2062 mm x 2547 mm (81.2” x 81.2” x
- 100”)
- Weight: 25 kg (55.12 lbs)
Dokument
Alternativ
Video
The TBLLA-2M is a large loop antenna (LLA) with three orthogonal loops, as required by CISPR 16 -1-4 and CISPR 15 / EN 55015.
The LLA is used to measure the current induced by the magnetic field emitted by luminaries. Section 4.4 of EN 55015 specifies the test setup and measuring procedures.
The TBLLA-2M consists of three perpendicular 2-meter diameter loop antennas on three orthogonal planes (X/Y/Z), set on lightweight hollow WPC frames with a total height of 2.5m. The loops lowest point is 0.5m above ground. Each loop element receives magnetic field radiation normal to the containing plane and generates a voltage signal proportionate to the strength of the H -field radiation at the output port of the RF transducer connected to the loop.
The TBLLA-2M is equipped with three TekBox TBCCP1-2K70 coaxial RF current monitoring probes (transducers), with a flat transfer impedance of 0 dBΩ (1V/A) from 9 kHz to 30 MHz when loaded with 50Ω. The kit comprises all required coaxial cables, ferrite clamps, a manual RF coaxial switch to select loops, and a TBTP3 tripod with a plastic DUT support plate.
A calibration dipole with support structure is available as optional accessory.
SPECIFICATIONS
- Type: Large Loop Antenna (triple loop)
- Frequency range: 9 kHz– 30 MHz
- Standards: CISPR 16-1-4, CISPR 15
- Loops: 3 perpendicular loops with 2m diameter
- Loop construction: RG223U sections with over-molded slits inside PEX tube
- RF transducer transfer impedance: typical 0 dBΩ ; 1V/A @ 9kHz to 30 MHz
- RF transducer output connector: N-female, 50 Ω
- Antenna validation factor: within ±2 dB compared to the theoretical validation factor for 2m diameter LLA given in CISPR 16-1-4
- Effective antenna correction factor: 0 dB
- CM resistance of the ferrite absorbers: > 200 Ω @ 10 MHz
- Mechanical Dimensions: L x W x H: 2062 mm x 2062 mm x 2547 mm (81.2” x 81.2” x
- 100”)
- Weight: 25 kg (55.12 lbs)